IP Office
5420/2420 Phone User Guide
Issue 6d (15th September 2005)
Table of Contents
5420/2420 Phone User Guide
Page ii
IP Office
Issue 6d (15th September 2005)
Table Of Contents
5420/2420 Phone User Guide
Page iii
IP Office
Issue 6d (15th September 2005)
The Telephone
Overview
This guide covers the use of the Avaya 5420 and 2420 phones on Avaya IP Office. Both phones are
similar, however the 5420 is only supported on the IP Office whereas the 2420 is supported on a range
of Avaya phone systems.
5420/2420 Phone User Guide
Page 4
IP Office
Issue 6d (15th September 2005)
The Telephone
1. Display, Call Appearance and Feature buttons: Call Appearance Keys allow the user to
handle multiple calls and the display shows call information. Details on system features
(allocated by your System Administrator) can also be displayed.
2. Message lamp: Lit when the user has voicemail messages. Can also be set to flash when the
phone is ringing.
3.
Previous/Next Page: Move through the different pages of the call handling, speed dials
and call log screens. Also used to move the cursor during data entry.
Messages: Access the user's mailbox.
4.
5. Call Handling Buttons:
·
Hold: Place call on hold.
·
Transfer: Transfer call.
·
Conference: Conference held calls.
·
Drop: Drop call.
·
Redial: Redial last number dialed.
6. Dial pad: Standard 12-button pad for dialing telephone numbers.
Volume Controls: Adjust the speaker, handset, headset, or ringer volume depending on
7.
which is currently in use.
Mute: Turns the microphone on/off. When in use, the associated light is on and the caller
8.
cannot hear you.
Headset: Switches from handset to headset. The light associated with this button turns on
9.
when the headset is active.
10.
Speaker: Access the speakerphone. The light associated with this button turns on when the
speakerphone is active.
Exit: Returns you to the main call handling screen.
11.
12. Softkeys: Used to navigate to or initiate certain features, such as Speed Dial or Call Log, as well
as control certain actions within the features. These keys correspond to the text prompts in the
display screen immediately above them.
5420/2420 Phone User Guide
Page 5
IP Office
Issue 6d (15th September 2005)
2420user
Call Appearance Keys
Normally, the first page of the main call handling screen contains three keys set as 'call appearance'
keys. These are allocated to you by your System Administrator and are indicated as a=, b= and c=.
Your System Administrator can change a call appearance key with:
·
A Bridged Appearance
A bridged appearance key matches the status and operation of the Call Appearance Key on a
pre-defined colleague's telephone. Hence, you can pick-up, make and receive calls on behalf of
your colleague.
·
A Line Appearance
An IP Office exchange line (but not IP lines) can be allocated to you such that the status of that
line is displayed and you can use the line appearance key to make and receive calls.
·
Call Coverage Appearance
A call coverage appearance key alerts you when a pre-defined colleague is receiving a call. The
covered user does not need to be using call appearance keys. Hence, you can pick-up calls on
behalf of your colleague.
All of the above can only be allocated to you by your System Administrator.
For details of Bridged, Line and Call Coverage Appearance Keys set-up and their operation, refer the IP
Office Key and Lamp Operation manual.
CAUTIONS:
1. Having more than two Call Appearance keys is very useful. When holding a call you can
answer/make another call and then switch between calls or transfer or conference. If you are set
to receive call waiting indication, the waiting call is shown against the next call appearance key.
2. Although the System Administrator can replace the Call Appearance Keys with:
·
A Bridged Appearance
·
A Line Appearance
·
Call Coverage Appearance
·
System Features
This would severely restrict the use of features such as conference and transfer.
It is for these reasons that it is strongly recommended that all Call Appearance keys remain at their
default settings.
5420/2420 Phone User Guide
Page 6
IP Office
Issue 6d (15th September 2005)
The Telephone
Call Appearance Keys Icons
The icons displayed against the Call Appearance/Feature Keys allow you to determine the status (for
example, on Hold) of each call. Icons also indicate whether a feature has been activated for a particular
button.
·
Incoming Call:
A symbol next to a call appearance key indicates an incoming call. Pressing the adjacent
key answers the call and puts any other current call on hold.
·
Connected:
A symbol next to a call appearance key indicates that it is the currently connected call. The
caller's telephone number (if available) is also shown. Pressing the adjacent
key puts the
call on hold. An H is also shown on the display.
·
On Hold:
A symbol next to a call appearance key indicates a call on hold. Pressing the adjacent
key takes the call off hold and puts any other current call on hold.
·
Function Active:
The button to the left or right of the function key is active.
System Features
System Features can only be set against soft Function Keys by your System Administrator. However,
your System Administrator may allocate you two `self administrator' features that will enable you to add
System Features to your soft Function Keys.
In addition, there are a number of System Features that you can always access yourself by the use of
short codes. Refer to System Features Introduction for details of System Features that you can always
access yourself by dialing short codes, for example *17 to listen to your voicemail messages.
5420/2420 Phone User Guide
Page 7
IP Office
Issue 6d (15th September 2005)
Basic Call Handling Features
Answer a Call
When a call arrives at your phone, you hear a ringing tone and a blinking bell icon appears on the
associated call appearance.
To answer an incoming call
Do one of the following:
·
If you are not active on another call, answer the call using your handset, headset, or
speakerphone (see Speakerphone).
·
If you are active on a call already, place the active call on hold (Hold), and then answer the
incoming call.
·
If the call appearance for the ringing call is not displayed on the current screen page, use
Exit to return to the first page of the Home screen. When you locate the call appearance for the
ringing call, press the corresponding call appearance button.
Make a Call
You can make calls from the phone using a variety of methods as follows:
To manually make a call:
1. Dial the required number on the key pad (remember to include the required access code (for
example, 9) for an outside line) and listen to the progress of the call.
2. Adjust speakerphone volume as necessary.
·
To change the volume use the and
buttons. The display shows the volume level.
(There are eight volume levels.)
3. If the call is not answered, you can clear the call by pressing
Speaker or
Drop
or
4. When the call is answered, either speak or pick up the handset and speak to the called party.
To automatically make a call:
Do any of the following:
·
Press
Redial and a call appearance key
to have the phone dial the last number that you
dialed. See Redial.
or
·
Access the Call Log and initiate a call to a specific entry. See Making Calls from the Call Log.
or
·
Access the Speed Dial List in your personal directory and initiate a call to a specific entry. See
Dialing a Speed Dial Number.
·
When the call is answered, either speak or pick up the handset and speak to the called party.
5420/2420 Phone User Guide
Page 8
IP Office
Issue 6d (15th September 2005)
Basic Call Handling Features
Clearing a Call
To clear an established call either:
1. Replace the handset
or
Drop. You will hear dial tone, unless you are in `call center mode' of working when you
2. Press
will then hear silence.
Headset Working
When a headset is to be used, it must be plugged in to the headset socket on the base of the phone. To
activate the headset and switch off the handset, press
Headset. The lamp beside the button is
illuminated when headset working is activated.
To answer an incoming call:
1. Press the call appearance key
next to the flashing bell icon ( ):
To clear a headset call:
1. Press
Drop.
To manually make a call:
1. Dial the number (remember to include the required access code (for example, 9) for an outside
line) and listen to the progress of the call.
To automatically make a call:
Do any of the following:
·
Press
Redial and a call appearance key
to have the phone dial the last number that you
dialed. See Redial
or
·
Access the Call Log and initiate a call to a specific entry. See Making Calls from the Call Log.
or
·
Access the Speed Dial List in your personal directory and initiate a call to a specific entry. See
Dialing a Speed Dial Number.
·
When the call is answered, speak to the called party.
5420/2420 Phone User Guide
Page 9
IP Office
Issue 6d (15th September 2005)
2420user
Speakerphone
The two-way built-in speakerphone allows you to make and answer calls without lifting your handset.
Keep in mind that two-way speakerphones may not operate satisfactorily in every environment (such as
in very noisy locations).
To make or answer a call without lifting the handset, or to use the speakerphone with any feature
1. Press
Speaker. The LED beside the button illuminates.
2. Make or answer the call, or access the selected feature.
and
buttons.
3. Adjust the speakerphone volume if necessary. To change the volume use the
The display shows the volume level. (There are eight volume levels).
To change from the speakerphone to the handset (or headset if fitted)
1. Pick up the handset (or press
Headset) and talk.
To change from the handset to the speakerphone
Speaker.
1. Press
2. Hang up the handset.
To end a speakerphone call
Speaker again.
1. Press
Speed Dial
The Speed Dial feature allows you to have the phone automatically dial calls to telephone numbers
stored in your personal directory (maximum of 104). See Dialing a Speed Dial Number.
To make a call to a personal directory entry using the Speed Dial feature
1. From the Home screen, press the
SpDial softkey. The Speed Dial screen is displayed.
2. Press the button next to the entry you want to call.
3. If the entry you want is not displayed, use and to cycle through the entries or key the first
letter of the required name to jump to the page with a matching entry.
4. The phone dials the number for you.
Redial
The Redial feature automatically redials a previously dialed extension or outside number (up to 24
digits). Your phone stores the last ten numbers dialed.
Note: If you have dialed the same number twice in succession, it will only have one appearance in the
redial list.
To redial previously dialed number:
1. Press
Redial. Use
and to step through the entries. When you have located the
required number, press the associated key.
5420/2420 Phone User Guide
Page 10
IP Office
Issue 6d (15th September 2005)
Basic Call Handling Features
Mute
During an active call, the Mute feature prevents the party with whom you are speaking from hearing you.
This feature is most commonly used in conjunction with the Speakerphone, but can be used to hold an
off-line conversation at any time during a call.
Preventing the other person on the line from hearing you:
1. Press Mute. The other party cannot hear you. The indicator next to the Mute button lights when
Mute is active.
Mute again.
2. To reinstate two-way conversation, press
Hold
If, with a call in progress, a second call arrives and is shown against a Call Appearance key, you can
then Hold the first call and answer the second call.
To put an existing call on hold:
1. Press
Hold or the Call Appearance button with the
symbol against it. The symbol changes to
; showing that the line is on hold.
2. Answer the second call by pressing the Call Appearance button with the symbol against it. The
symbol changes to ; showing that the line is connected.
To return to the held call:
1. If you have a call in progress, then first put that call on hold as above.
against it.
2. To retrieve a held call, simply press the Call Appearance button with the
Note: After a pre-set time (defined by your System Administrator), you are reminded that you have a call
on hold by the hold icon changing for a few moments to and the phone ringing.
5420/2420 Phone User Guide
Page 11
IP Office
Issue 6d (15th September 2005)
2420user
Transfer
The Transfer feature allows you to transfer a call from your telephone to another extension or outside
number.
To transfer the current call to another extension:
1. With a call in progress, press
Transfer or
Hold.
2. When you hear dial tone, dial the number to which the call is to be transferred.
3. Do one of the following:
·
To transfer the call without announcing it, either hang up or press
Transfer again. The
transfer is complete. If the transferred call is not answered within a preset time, it is
returned to you.
·
To announce the call before transferring it, wait for the called party to answer.
·
If the called party is willing to accept the call, press
Transfer again to complete
the transfer.
·
If the called party does not wish to accept the call, press
Drop. You can return
to the held call by pressing its call appearance button.
·
If the line is busy or if there is no answer, press
Drop. You can return to the held call
by pressing its call appearance button.
To transfer a new call to a held call using Conference:
1. With a call in progress and you wish to make an enquiry call or another call arrives, press
Hold. Make or answer the second call. The second call requires to be transferred to the first
held call.
Conference and then
Drop. The transfer is
2. To transfer the new call to the held call, press
complete.
5420/2420 Phone User Guide
Page 12
IP Office
Issue 6d (15th September 2005)
Basic Call Handling Features
Conference
The Conference feature allows you to conference other parties (including yourself) into a call.
Notes:
1. The number of parties allowed in a conference is controlled by your telephone system.
2. Two Call Appearance keys are required for the conference feature.
To add another party to a call:
Conference
1. Press
2. Dial the number of the person you want to add to the call.
3. Wait for an answer. If the called party does not answer or does not want to join the conference,
press Drop.
Conference again. You can return to the held call by
4. To add the person to the call, press
pressing its call appearance button.
5. Repeat steps 1 through 4 for additional conference connections.
To add a held call(s) to an active call:
Conference.
1. Press
2. All held calls are added to the conference.
To leave a conference call:
Drop.
1. To leave a conference, press
Message
Your Message lamp turns on when a caller has left a message for you.
Message button to retrieve your messages, and follow the prompts.
Press the
5420/2420 Phone User Guide
Page 13
IP Office
Issue 6d (15th September 2005)
Using Speed Dials
Overview of Speed Dials
The phone can store up to 104 personal speed dials. The list of these speed dials is accessed by
pressing
SpDial. If
SpDial is not shown, press
Exit top exit the current screen.
·
The speed dial list is sorted alphabetically.
·
Press
and
to move between pages.
·
Press the appropriate letter key to move direct to the first page with a matching name.
·
Press the
or
next to an entry to call the associated number.
·
Use the
key options to perform other actions.
Add or
Edit gives access to the details of a particular speed dial.
Pressing
Note: Speed dials can be used for any numbers that can be manually dialed from the extension. Where
a dialing prefix is required (for example an external line access digit; usually 9) then that prefix must be
part of the speed dial number.
Dialing a Speed Dial Number
You can use the speed dial directory to make a call with the handset on hook or off hook.
SpDial. If
SpDial is not shown, press
Exit to exit the current screen.
1. Press
2. Press and to display different pages of speed dials or key the first letter of the required
name to jump to the page with a matching entry.
or
key.
3. When the required entry is displayed, press the adjacent
5420/2420 Phone User Guide
Page 14
IP Office
Issue 6d (15th September 2005)
Using Speed Dials
Deleting a Speed Dial
1. Press
SpDial. If
SpDial is not shown, press
to exit the current screen.
Delete.
2. Press
3. Select the speed dial entry you want to delete. Press and to display different pages of speed
dials or key the first letter of the required name to jump to the page with a matching entry.
or
key. A request for
4. When the required entry is displayed, press the adjacent
confirmation will appear.
Yes to delete the entry or
Cancel to exit without deleting.
5. Press
Done to return to the speed dial list.
6. Select another entry to delete or press
Editing a Speed Dial
1. Press
SpDial. If
SpDial is not shown, press
to exit the current screen.
Edit.
2. Press
3. Select the speed dial entry you want to edit. Press and to display different pages of speed
dials or key the first letter of the required name to jump to the page with a matching entry.
4. When the required entry is displayed, press the adjacent
or
key.
5. Edit the speed dial using the same methods as for adding a new speed dial. See Adding a New
Speed Dial.
6. After saving or canceling any changes you will be returned to the speed dial selection list. Select
Done to return to the speed dial list.
another speed dial to edit or press
Converting a Call Log Entry to a Speed Dial
You can create a new speed dial from a call log entry. See Saving a Call Log Entry to Your Speed Dial
List.
This process will start the normal speed entry screen but pre-filled with the name and number from the
call log entry.
5420/2420 Phone User Guide
Page 15
IP Office
Issue 6d (15th September 2005)
2420user
Adding a New Speed Dial
1. Press
SpDial. If
SpDial is not shown, press
to exit the current screen. Press
Add. If a message stating that the speed dial list is full appears, you must first delete an existing
entry before adding any new entry. See Deleting a Speed Dial.
·
You can switch between Name and Number entry by pressing the
key next to the
item you want to edit. The
options also change accordingly.
2. With Name selected, begin entering text using the telephone keypad. Each key is marked with
the letters and number it provides. You may have to press the key more than once depending on
the character you require.
·
For example, the key 2 is also marked as A, B and C. To enter a C, press 2 until a C is
displayed.
·
If the next character you want to enter is on the same key, press
to move the cursor
right and then enter the character.
·
By default the first letter is entered in upper-case and the phone then switches to lower-
case entry mode. To change the case of the current character press
Case.
·
To enter a space press
Space.
·
If you make a mistake, use
Backspace to delete the character to the left of the
cursor.
·
If you have made a mistake in the middle of a character string and do not wish to
backspace and re-enter all the characters, use the key to step back to one character
before the point where you wish to edit. Either insert the new character or press
Backspace to delete the character to the left of the cursor.
·
Pressing the * key once enters a . (period) or twice a *. To enter more than one * or
period, press to move the cursor to the right and then enter the character.
·
Pressing the # key once enters a (dash) or twice enters a #. To enter more than one #
or dash, press to move the cursor to the right and then enter the character.
3. When the name is set as required, select Number.
4. Enter the number required using the dialing keypad. For external numbers remember to enter
any external dialing prefix required (9 say).
·
To enter a hyphen, press
Hyphen. This does not affect the number dialed but may
help make numbers more readable.
·
To enter a 1.5 second pause, press
Pause. This will appear as a , (comma) character
in the telephone number.
·
Use the
and
keys to move the cursor left or right.
Save.
5. To save the speed dial and return to the speed dial list, press
Cancel.
6. To return to the speed dial list without saving the changes press
Exit.
7. To return to the call handling screen without saving the changes press
5420/2420 Phone User Guide
Page 16
IP Office
Issue 6d (15th September 2005)
Using the Call Log
Overview of the Call Log
The phone maintains a call log, accessed by pressing
Log. This log can store up to 100 entries.
These can be a combination of incoming answered calls, incoming unanswered calls and outgoing calls
You can select which types of calls are included in the log. You can also use call log entries to make
return calls or convert the entry into a speed dial for future use.
·
WARNING:
Calls that are made using pin codes and other information will appear in the call log. Either
Logging of outgoing calls should be switched off or those call logs removed manually. See
Setting Which Calls are Logged.
Notes:
1. Only outgoing calls made using the dial pad or a SpDial entry are logged.
2. Call log entries are lost if the phone is disconnected from the IP Office.
Log is pressed a screen similar to the following is displayed:
When
·
Missed calls are displayed first. You can select from InAns or Outgo. Alternatively, press More
and select All to display all three options.
·
Logged calls are shown with the most recent first.
·
The name of the called or calling party is shown if available.
·
The number of the called or calling party is shown.
·
Press
and
to display further pages of entries.
·
Pressing the
or
key next to a log entry display further details of that particular call.
·
The number of the log entry
·
The type of log entry, i.e. Answered, Un-answered or Outgoing.
·
The name of the called or calling party is shown (if available).
·
The number of the called or calling party is shown.
·
The date and time of the call.
·
Press
and
to display the previous or next logged call.
·
The
keys provide a number of actions.
5420/2420 Phone User Guide
Page 17
IP Office
Issue 6d (15th September 2005)
2420user
Using The Call Log
You can make calls directly from the call log. Whilst in the call log you can still make a call by going off-
Speaker and dialing a new call. Similarly, you can still receive calls and handle them
hook, pressing
using the dial pad key functions.
Viewing the Call Log
1. Press
Log. If
Log is not shown press any soft key
2. At default, Missed calls are displayed first. You can select from InAns or Outgo. Alternatively,
press More and select All to display all three options. To return to Missed or InAns or Outg,
press Back and make your selection.
and
to display different pages of log entries.
3. Press
·
To exit the call log and return to the previous screen press
Done.
·
To exit the call log and return to the call handling screen press
.
·
To view the details of a particular log entry, press the
or
key next to the entry.
Done to return to the previous screen.
4. Press
Making Calls from the Call Log
1. Press
Log. If
Log is not shown press any soft key
2. At default, Missed calls are displayed first. You can select from InAns or Outgo. Alternatively,
press More and select All to display all three options. To return to Missed or InAns or Outg,
press Back and make your selection.
or
key next to the entry.
3. When you locate the entry you want to call, press the
Call make the call.
4. Press
·
If the number shown is external but doesn't include the external dialing prefix used by
your telephone system, go off-hook, dial the prefix and then press
Call.
Saving a Call Log Entry to Your Speed Dial List
1. Press
Log. If
Log is not shown press any soft key
2. At default, Missed calls are displayed first. You can select from InAns or Outgo. Alternatively,
press More and select All to display all three options. To return to Missed or InAns or Outg,
press Back and make your selection.
and
to display different pages of log entries.
3. Press
or
key next to the entry.
4. When you locate the entry you want to call, press the
Save. The speed dial editing screen appears, pre-filled with the details from the call
5. Press
log entry. See Adding a New Speed Dial.
5420/2420 Phone User Guide
Page 18
IP Office
Issue 6d (15th September 2005)
Using the Call Log
Deleting a Call Log Entry
1. Press
Log. If
Log is not shown press any soft key
2. At default, Missed calls are displayed first. You can select from InAns or Outgo. Alternatively,
press More and select All to display all three options. To return to Missed or InAns or Outg,
press Back and make your selection.
and
to display different pages of log entries.
3. Press
or
key next to the entry.
4. When you locate the entry you want to call, press the
Delete. The entry is deleted from the Call Log and the details of the next call are
5. Press
shown.
6. To exit the call log and return to the call handling screen press
Exit.
Erasing All Logged Calls
Loss of power to the phone will cause all call log entries to be deleted.
The Erase All option deletes the calls you have selected to log. See Setting Which Calls are Logged.
Caution: This action also deletes all speed dial entries and phone personalization options. See Default
Phone/Erase All Settings.
Log. followed by More.
1. Press
2. Press Delete. You are presented with a message asking you to confirm that you want to delete
all entries.
3. Press Erase to remove all logged entries
Setting Which Calls are Logged
Caution: If you change these settings, any call details already in the call log that no longer match the
selection are deleted.
Option. If
Option is not shown, press
to exit the current screen.
1. Press
Log Setup.
2. Press
A menu showing Answered, Un-Answered and Outgoing, with their current settings, is
displayed.
key next to it. Alternatively, press
3. To toggle a particular setting between Yes or No, press the
the
key next to a call type to underline its current setting and then press Yes/No to change
the value of the currently underlined setting.
4. Do one of the following: Note: If you press Save after changing the settings, any existing call log
entries that do not match the call types selected are deleted from the call log.
·
To save the settings and return to the options menu, press Save.
You will hear a confirmation tone.
·
To return to the Options menu without saving any changes, press Cancel.
·
To return to the call handling screen without saving any changes, press
Exit.
5420/2420 Phone User Guide
Page 19
IP Office
Issue 6d (15th September 2005)
Changing Options
Changing Ringer Options
The IP Office uses 'distinctive ringing' for different types of calls - a repeated single ring for internal calls,
a repeated double ring for external calls and a single ring followed by two short rings for ringback calls.
These options are fixed by the IP Office. The phone's own menus allow its ringer sound to be
personalized so you can recognize it from other ringing phones.
To change the ringer sound:
You can choose from among eight different ring sounds. This alters the tone and style of ringing used by
the phone, the ring pattern is still controlled by the IP Office according to the call type. Note: If you
receive a call while selecting a ringer sound, you are automatically returned to the call handling screen.
1. Press
Exit to exit any other mode, then press any of the
keys below the display.
Option.
2. Press
Ring Options followed by
Ring Pattern. A menu with the current ring pattern
3. Press
appears.
and
keys or press a dial pad key between 1 and 8.
4. To select a ringing pattern use either the
You will hear the selected ringing pattern.
Play or repress the dial pad key.
5. To hear the ringing pattern again press
·
When you have selected a ringing pattern, press
Save. You will hear a confirmation
tone and be returned to the options menu.
·
If you want to return to the options menu without changing the ring pattern, press
Cancel.
To use the Message Lamp for ringing alerts:
Exit to exit any other mode, then press any of the
keys below the display.
1. Press
Option.
2. Press
Ring Options and set Flash Message Lamp to Yes or No. When set to Yes the
3. Press
Message lamp will flash when you receive a call.
·
Changing this option does not affect the voicemail visual indicator feature.
To automatically show the call handling screen:
Exit to exit any other mode, then press any of the
keys below the display.
1. Press
Option.
2. Press
Ring Options and set Show Phone Screen to Yes or No. If set to Yes then, when
3. Press
you are setting up/using Speed Dial, Call Log, etc, you are automatically returned to the call
handling screen when you receive a call.
5420/2420 Phone User Guide
Page 20
IP Office
Issue 6d (15th September 2005)
Function Keys
Adjusting the Display Contrast
You can adjust the contrast level on the telephone display. You can choose from among fifteen levels of
contrast.
1. Press
Exit to exit any other mode. Press
Option.
2. Press
Contrast. A menu with the current contrast setting appears.
and
keys to adjust the level of contrast.
3. Use the
4. When the contrast is set as required, either:
·
Return to the options menu by pressing
Done.
·
Return to the call handling screen by pressing
Exit.
Call Log Setup
Through the Option menu you can specify which types of calls should be included in the phone's call
log. See Setting Which Calls are Logged.
Miscellaneous
This option only contains one menu item: Stay in Speed Dial.
When set to Yes and you access your personal Speed Dial list the menu will remain displayed
regardless of any calls made or received.
Exit to exit any other mode. Press
Option..
1. Press
Miscellaneous and set Stay in Speed Dial to Yes.
2. Press
Using Self Test
Self test can be used to display information about the phone and to check operation of the lamps and
display. The information may be required by a telephone system maintainer.
Exit to exit any other mode. Press
Option.
1. Press
Self Test. The a screen of information appears.
2. Press
Test key. The screen lines should all go black and all the phone lamps
3. Press and hold the
should come on.
4. Do one of the following:
·
To return to the options menu, press
Done.
·
To return to the call handling screen, press
.
Selecting the Display Mode
See Display Mode.
5420/2420 Phone User Guide
Page 21
IP Office
Issue 6d (15th September 2005)
2420user
Default Phone/Erase All Settings
The Erase All option allows you to reset all personalized settings entered through the phone's Option
menus (except contrast level). It also deletes all entries in the phones Call Log and Speed Dial lists.
1. Press
Exit to exit any other mode. Press
Erase....
2. Press the
key next to an items to select/de-select it for erasure. A is shown next to selected
items. The items selectable for erasure are:
·
Speed Dials: Selects for erasure all speed dials set in the phone's SpDial store.
·
Call Log: Selects for erasure all entries in the phone's call log.
·
User Labels: Selects for erasure all customized function key labels.
·
Language: Selects to default the phone's language setting back to default.
·
Options: Any for erasure or defaulting all other phone options.
·
All: Selects for erasure or defaulting all of the above.
Erase or
Cancel.
3. Press
Language
When the phone is first installed, it is set to display screen text in English. You can select the language
that you would prefer from the following:
·
English, German (Deutsch), French (Français), Spanish (Español), Italian (Italiano), Dutch
(Nederlands), Portuguese (Português) or Japanese (Katakana characters).
Note: This does not alter your user language setting on the telephone system.
Exit to exit any other mode. Press
Option.
1. Press
Language. A menu listing the available languages appears, with the current language
2. Press
underlined.
or
key next to the language required. The screen text changes to the language
3. Press the
selected.
4. Do one of the following:
·
To save the settings and return to the options menu, press
Save. You will hear a
confirmation tone.
·
To return to the options menu without saving any changes, press
Cancel.
·
To return to the call handling screen without saving any changes, press
.
5420/2420 Phone User Guide
Page 22
IP Office
Issue 6d (15th September 2005)
Function Keys
Automatic Gain Control (AGC)
Automatic Gain Control (AGC) raises the volume when a caller is speaking quietly and lowers the
volume when the caller is loud.
1. Press
Exit to exit any other mode. Press
Option.
2. Press a or
key until a menu listing the current handset, headset and speaker AGC options is
displayed.
key next to it.
3. To toggle a particular setting between Yes and No, press the
·
Alternatively, press the
key next to a call type to underline its current setting and then
press
Yes/No to change the value of the currently underlined setting.
4. Do one of the following:
·
To save the settings and return to the options menu, press
Save. You will hear a
confirmation tone.
·
To return to the options menu without saving any changes, press
Cancel.
·
To return to the call handling screen without saving any changes, press
Exit.
5420/2420 Phone User Guide
Page 23
IP Office
Issue 6d (15th September 2005)
System Features
System Features
As well as your phones specific features, you can access a number of system features by dialing short
codes.
These instructions are for the system's default configuration. They assume that you are using the default
feature codes. It also assumes that you have full access to all features and the public telephone network.
Making Calls
Internal Calls:
If your System Administrator has allocated you the Ring Back When Free feature (see RBak+ - Ringback
When Free) under a dial pad digit, you can:
1. When you call an extension that does not answer or is busy, press the
RBak feature key to
set a callback on that extension.
2. When the extension you called becomes free, your phone will ring (a burst of three rings).
3. Lift the handset and the extension is called automatically.
4. When the extension you called is free, your phone will ring (a burst of three rings).
5. Lift the handset and the extension is called automatically.
External calls:
To make an external call, either dial the number (prefixed by the access code if required) or use a speed
dial code (contact your system manager for a list of your speed codes).
If you hear busy tone while dialing, then the call may be barred. Your system manager can bar certain
calls, such as those to premium rate numbers and international calls.
Answering Calls
Ringing at your own extension:
Simply pick up the handset. When in headset mode, press the button associated with the alerting call.
The default ringing cadences are:
·
Internal calls have a single ring cadence
·
External calls have a double ring cadence.
These can be changed by your System Administrator.
Ringing at another extension:
You can answer from your own phone by using Call Pick-Up; lift your handset and dial:
·
*30 to answer a call ringing anywhere.
·
*31 to answer a call within your group.
·
*32*201# to answer the call for a particular extension, in this example 201.
Note: If your phone rings for any longer than a specified period (15 seconds in default), any re-direction
feature that you have activated, such as voicemail or call forwarding, will come into effect.
5420/2420 Phone User Guide
Page 24
IP Office
Issue 6d (15th September 2005)
System Features
Call Forwarding
Your calls can be forwarded to another extension or an external number either when you are away from
your desk (on no answer), when your extension is busy, and all calls (for example when you go on
holiday).
To switch forward direct station (i.e. not Hunt Group) calls on dial *01, to switch it off
·
dial *02.
·
To switch forward on busy on dial *03, to switch it off dial *04.
·
To switch forward on no answer on dial *05, to switch it off dial *06.
·
To set the number to which your calls are forwarded dial *07*201#, forwarding to 201 in this
example.
Diverting Calls
You can divert your calls to another extension. In the examples below N is the extension to which you
want your calls diverted. Note that, if you do not answer calls at the temporary extension, they are
forwarded to your own voicemail or call forwarding number.
At another extension:
·
*12*N# from the extension you are temporarily using.
·
*13*N# to re-direct the calls back to your own extension, before you return to it.
At your own extension:
·
*14*N# from your own extension.
·
*14*# to cancel either feature from your own extension.
Do Not Disturb
You may choose to receive no calls at all or only those from particular callers on your exceptions list:
To switch Do Not Disturb on (with or without exceptions) dial *08, to switch it off dial *09.
·
*10*N# to add a number to the exception list.
·
*11*N# to delete a number from the exception list.
Note: Your callers, other than your exceptions, either hear busy tone or are re-directed to your
voicemail.
5420/2420 Phone User Guide
Page 25
IP Office
Issue 6d (15th September 2005)
2420user
Voicemail
Note that not all systems support voicemail or have voicemail installed.
·
To switch voicemail on dial *18, to switch it off dial *19.
·
To retrieve your voicemail, use the code *17.
Your voicemail may be set up to deliver your messages by calling you whenever you hang up: this
feature is known as Voicemail Ringback.
·
To turn Voicemail Ringback on dial *48; to turn it off dial *49.
Dialing a number while listening to your messages invokes further facilities:
Once messages have been delivered, they are held on the system for 24 hours (this is fixed for
Voicemail Lite, but can be varied by your System Administrator if your IP Office is equipped with
VoicemailPro).
You can collect your voicemail from another extension by using the PIN your System Administrator has
set up for you. You can collect your messages if you are out of the office, by either dialing from a number
that has been registered for the purpose or by dialing your extension number and PIN when prompted. If
validation is successful, then dial 1 to retrieve your mail.
The System Administrator also specifies the reception number, to which the call is diverted if the caller
dials 0, and your email address if your voicemail and email are integrated.
5420/2420 Phone User Guide
Page 26
IP Office
Issue 6d (15th September 2005)
System Features
Default Feature Codes
The following are the normal default feature codes available to all users. Your System Administrator may
add additional codes for other features and for speed dials.
The N where shown, should be replaced by the appropriate number. For example, with *07*N#, replace
N with the extension to which you want your calls forwarded when you have forwarding switched on.
*00
Cancel All Forwarding
*32*N#
Call Pick Up Extension
*01
Forward Unconditionally On
*33*N#
Call Queue
*02
Forward Unconditionally Off
*34
Hold Music
*03
Forward on Busy On
*35*N#
Extn Login
*04
Forward on Busy Off
*36*N#
Extn Logout
*05
Forward on No Answer On
*37*N#
Park Call
*06
Forward on No Answer Off
*38*N#
Ride Call
*07*N#
Forward to number
*39
Relay On
*08
Do Not Disturb On
*40
Relay Off
*09
Do Not Disturb Off
*41
Relay Pulse
*10*N#
Do Not Disturb Exception Add
*42
Relay On
*11*N#
Do Not Disturb Exception Delete
*43
Relay Off
*12*N#
Follow Me Here
*44
Relay Pulse
*13*N#
Follow Me Here Cancel
*45*N#
Call Steal
*14*N#
Follow Me To
*46
Call Steal
*15
Call Waiting On
*47
Conference Add
*16
Call Waiting Off
*48
Voicemail Ringback On
*17
Voicemail Collect
*49
Voicemail Ringback Off
*18
Voicemail On
*50
Forward Hunt Group Calls On
*19
Voicemail Off
*51
Forward Hunt Group Calls Off
*20*N#
Set Hunt Group Night Service
*52
Clear Call
*21*N#
Clear Hunt Group Night Service
*53*N#
Call Pickup Members
*29
Toggle Calls
*57*N#
Forward on busy number
*30
Call Pick Up Any
*70*N#
Dial Physical Extn by Number
*31
Call Pick Up Group
*71*N#
Dial Physical Extn by ID
5420/2420 Phone User Guide
Page 27
IP Office
Issue 6d (15th September 2005)
EU24 Expansion Module
EU24 Overview
The EU24 Expansion Module is an optional device that can be connected to your 2420/5420 phone to
extend the number of call appearance and feature buttons available on the telephone.
The expansion module has 24 buttons arranged in two columns. Depending on how they have been
programmed by your System Administrator, these buttons can be used for call appearances or features.
You can adjust the viewing angle of the EU24 display to match that of your phone.
The following figure shows a top view of the EU24 (the left hand column is displayed).
1. Call Appearance/Feature Button.
2. Feature Active icon for feature in right column.
3. Alternate Display Button
4. Feature Active icon for feature in left column.
5. Display.
5420/2420 Phone User Guide
Page 28
IP Office
Issue 6d (15th September 2005)
EU24 Expansion Module
Connection
Before you can begin using the EU24 Expansion Module, the module must be connected to the phone
according to the instructions in the EU24 Expansion Module Installation and Safety Instructions (555-
233-136).
5420/2420 Phone User Guide
Page 29
IP Office
Issue 6d (15th September 2005)
2420user
Using the EU24 Expansion Module
The following sections explain how to use the features of the EU24 Expansion Module. For more
information, consult your System Administrator.
Viewing the Alternate Display
Although the EU24 Expansion Module supports an additional 24 call appearance/feature buttons, it only
displays the button labels and icons for one column at a time. A dotted line separates the left column
from the right column.
When you are viewing the labels and icons for the left column, the icons for the right column are
displayed to the right of the dotted line. To view the column not currently displayed, press the Alternate
Display button.
Selecting a Call Appearance/Feature Button
To select an available call appearance or feature, press the button next to the label in the column
currently displayed.
If the call appearance or feature is not currently displayed, use the Alternate Display key to access the
additional 12 call appearance/feature button labels.
Understanding Call Appearance/Feature Button Status Icons
When a call arrives for a call appearance on the EU24 Expansion Module, the bell icon blinks on the
corresponding call appearance. To answer the call, press the button associated with the call
appearance.
The icons displayed on the call appearance allow you to determine the status (for example, on hold) of
each call on the EU24 Expansion Module. Icons also indicate whether a feature has been administered
for a particular button on the EU24 Expansion Module. For an explanation of these icons see Call
Appearance Keys.
5420/2420 Phone User Guide
Page 30
IP Office
Issue 6d (15th September 2005)
Index
Call Waiting On 27
All 17, 18, 19
Call Appearance
0
Calls
All Logged Calls
Keys Icons 7
07*N 27
Answer 8
Erasing 19
Call
1
Answering 24
All Logged Calls 19
Appearance/Feature
1.5
Clearing 9
Alternate Display
Button
enter 16
Diverting 25
Viewing 30
Selecting 30
10*N 25, 27
Incoming 7
Alternate Display 30
Call
11*N 25, 27
Make 8
Alternate Display
Appearance/Feature
12*N 25, 27
Making 18, 24
button
Button 28
13*N 25, 27
Calls 7
press 30
Call
14*N 25, 27
Calls 8
Alternate Display
Appearance/Feature
2
Calls 8
button 28
Button 30
Calls 9
Alternate Display
Call
20*N 27
Calls 18
button 30
Appearance/Feature
201
Calls 24
Alternate Display key
Button Status Icons
forwarding 25
Calls 24
use 30
Understanding 30
21*N 27
Calls 25
Alternate Display key
Call
3
Cancel 15, 16, 19,
30
Appearance/Feature
32*N 27
20, 22, 23
Answer
Button Status Icons
33*N 27
Cancel All
Call 8, 24
30
35*N 27
Forwarding 27
showing 19
Call
36*N 27
Case 16
Answer 8
Appearance/Feature
37*N 27
CAUTIONS 6
Answer 19
Keys 7
38*N 27
Clear Call 27
Answer 24
Call Coverage
4
Clear Hunt Group
Answer/make 6
Appearance 6
Night Service 27
Answered, Un-
Call Coverage
45*N 27
Clearing
answered 17
Appearance Keys 6
5
Call 9
Appearance/feature
Call Forwarding 25
53*N 27
Clearing 9
30
Call Handling
57*N 27
Colleague's 6
Appearance/feature
Buttons 4
7
Conference 12, 13
button 30
Call Log
70*N 27
Conference Add 27
Automatic Gain
Access 8, 9
71*N 27
Connection 29
Control 23
Overview 17
Converting
Avaya 4
Viewing 18
A
Call Log Entry 15
Avaya 5420 4
Call Log 4
Access
Converting 15
Avaya IP Office 4
Call Log 8
Call Log 8, 9
Call Log 9
B
D
speakerphone 4
Call Log 17
Speed Dial List 8,
Back 18, 19
Default Feature
Call Log 18
9
Backspace 16
Codes 27
Call Log 18
Access 4
Bridged 6
Default Phone/Erase
Call Log 19
Access 8
Bridged Appearance
All Settings 22
Call Log 20
Access 9
6
Deleting
Call Log 22
Add
Busy Off 27
Call Log Entry 19
Call Log Entry
New Speed Dial
Busy On 27
Speed Dial 15
Converting 15
16
Deleting 15
C
Deleting 19
Pressing 14
Deleting 19
Call Appearance 6,
Saving 18
Add 14
Deutsch 22
13
Call Log Entry 15
Add 16
Dial
Call Appearance
Call Log Entry 18
Adjust speakerphone
Speed Dial
button
Call Log Entry 19
8
Number 14
pressing 11
Call Log Setup 21
Adjusting
Dial 14
Call Appearance
Call Pick Up Any 27
Display Contrast
Dial Physical Extn 27
button 11
Call Pick Up
21
Display Contrast
Call Appearance
Extension 27
speakerphone 10
Adjusting 21
Keys
Call Pick Up Group
Adjusting 10
Display Contrast 21
replace 6
27
Adjusting 21
Display Mode
Call Appearance
Call Pick-Up 24
Administrator' 7
Selecting 21
Keys 4
Call Pickup Members
Affect
Display Mode 21
Call Appearance
27
voicemail 20
Display, Call
Keys 6
Call Queue 27
Affect 20
Appearance 4
Call Appearance
Call Steal 27
AGC 23
Diverting
Keys 11
Call Waiting Off 27
5420/2420 Phone User Guide
Page 31
IP Office
Issue 6d (15th September 2005)
2420user
Follow Me To 27
Log 19
Calls 25
P
Forward Hunt Group
Diverting 25
Park Call 27
M
Calls Off 27
Do Not Disturb 25
Pause 16
Making
Forward Hunt Group
Done
Personalization 19
Call 8
Calls On 27
pressing 21
PIN 26
Calls 18, 24
Forward
Done 15, 18
Play 20
Making 8
Unconditionally Off
Done 21
Português 22
Making 18
27
Done 21
Portuguese 22
Making 24
Forward
Drop 8, 12, 13
Press Add 16
Menu
Unconditionally On
Press Call 18
E
Speed Dial list 21
27
Press Conference 13
Message 13, 20
Edit
Forwarding
Press Contrast 21
Message button
Speed Dial 15
201 25
Press Delete 15, 19
Press 13
Edit 14
Forwarding 25
Press Done 18
Message button 13
Edit 15
Français 22
Press Drop 9
Miscellaneous 21
Either Logging 17
Function Active 7
Press Edit 15
Missed
Email 26
Function Keys 7
Press Erase 19, 22
return 18, 19
End
Press Exit 20, 21,
G
Missed 18
speakerphone 10
22, 23
Missed 18
End 10
German 22
Press Hold 11
Missed 18
English 22
H
Press Language 22
Missed 19
Entering
Headset 9, 10
Press Log 18, 19
Mode' 9
1.5 16
Headset Working 9
Press Log Setup 19
More 17, 18, 19
Entering 16
Hold
Press Miscellaneous
Mute 11
Erase All 19, 22
Test key 21
21
Mute button 11
Erasing
Hold 7, 11, 12
Press Mute 11
All Logged Calls
N
Hold 21
Press Option 19, 20,
19
Hold Music 27
Name 16
21, 22, 23
Erasing 19
Home 8, 10
Nederlands 22
Press Redial 8, 9, 10
Español 22
Hunt Group 25
New Speed Dial
Press Ring Options
EU24
Hyphen 16
Adding 16
20
view 28
New Speed Dial 16
I
Press Save 18
EU24 28
No Answer Off 27
Press Self Test 21
ID 27
EU24 Expansion
No Answer On 27
Press SpDial 14, 15,
InAns 17, 18, 19
Module
Not Disturb 25
16
Incoming
Using 30
Not Disturb
Press Speaker 10
Call 7
EU24 Expansion
Exception Add 27
Press Yes 15
Incoming 7
Module 28, 29
Not Disturb
Pressing
Internal Calls 24
EU24 Expansion
Exception Delete 27
Add 14
IP 6
Module 30
Not Disturb Off 27
Alternate Display
IP Office 4, 6, 17, 26
EU24 Expansion
Not Disturb On 27
button 30
IP Office Key
Module Installation
Number
Call Appearance
refer 6
29
System Features
button 11
IP Office Key 6
EU24 Overview 28
7
Done 21
Italian 22
Exit
Number 7
Exit 21
Italiano 22
pressing 21
Number 16
Log 17
Exit 8, 14, 16, 19
J
Number 27
Message button
Exit 21
Japanese 22
O
13
Exit 23
K
RBak 24
On/off 4
Extn Login 27
SpDial 14
Katakana 22
Option 19, 20, 22
Extn Logout 27
SpDial softkey 10
Option menu
L
F
Speaker 8, 18
return 19
Lamp Operation 6
Feature 4
Pressing 8
Option menu 19
Language 22
Feature Active icon
Pressing 10
Option menu 21
LED 10
28
Pressing 11
Outg 18, 19
Line 6
Flash Message
Pressing 13
Outgo 17, 18, 19
Line Appearance 6
Lamp
Pressing 14
Overview
Log
set 20
Pressing 17
Call Log 17
pressing 17
Yes 20
Pressing 18
Speed Dials 14
Log 17
Flash Message
Pressing 21
Overview 4
Log 18
Lamp 20
Pressing 24
Overview 14
Log 18
Follow Me Here 27
Pressing 30
Overview 17
Log 18
Follow Me Here
Previous/Next Page
Log 19
Cancel 27
4
5420/2420 Phone User Guide
Page 32
IP Office
Issue 6d (15th September 2005)
Index
Speed Dial Number
up/using Speed
Using The Call Log
R
14
Dial 20
18
RBak
Speed Dials
Which Calls 19
press 24
V
Deleting 15
Yes 20, 21
RBak 24
Viewing
Editing 15
Set 19
Redial 4, 10
Alternate Display
Overview 14
Set 20
Redial list 10
30
Yes 21
Set 21
Redials 10
Call Log 18
Speed Dials 4, 10
Set Hunt Group
Refer
EU24 28
Speed Dials 14
Night Service 27
IP Office Key 6
Viewing 18
Speed Dials 15
Show Phone Screen
Refer 6
Viewing 28
Speed Dials 15
set 20
Relay Off 27
Viewing 30
Speed Dials 15
Yes 20
Relay On 27
Voicemail
Speed Dials 21
Show Phone Screen
Relay Pulse 27
affect 20
Speed Dials 22
20
Replace
Voicemail 4, 7
Standard 12-button 4
Showing
Call Appearance
Voicemail 20
Stay 21
Answered 19
Keys 6
Voicemail 24
System
Showing 19
Replace 6
Voicemail 25
Administrator 4, 6, 7,
Softkeys 4
Return
Voicemail 25
11, 24, 26, 27, 28, 30
Space 16
Missed 18, 19
Voicemail 26
System Features
Spanish 22
Options menu 19
Voicemail Collect 27
number 7
SpDial
Return 18
Voicemail Lite 26
System Features 6
pressing 14
Return 18
Voicemail Off 27
System Features 7
SpDial 14
Return 18
Voicemail On 27
System Features 24
SpDial 14
Return 19
Voicemail ringback
SpDial 15
Return 19
T
26
SpDial 15
Ride Call 27
Voicemail Ringback
Test key
SpDial 16
Ring Back When
Off 27
hold 21
SpDial 17
Free 24
Voicemail Ringback
Test key 21
SpDial 22
Ring Options 20
On 27
Toggle Calls 27
SpDial softkey
Ring Pattern 20
VoicemailPro 26
Transfer 12
press 10
Volume Controls 4
S
U
SpDial softkey 10
Safety Instructions
W
Un-Answered 19
Speaker
29
Understanding
WARNING 17
pressing 8, 18
Save
Call
Which Calls
Speaker 8
Call Log Entry 18
Appearance/Feat
Setting 19
Speaker 18
Save 16
ure Button Status
Which Calls 19
Speakerphone
Save 18
Icons 30
Access 4
Y
Save 19
Understanding 30
Adjust 10
Yes
Save 20
Up/using Speed Dial
end 10
Flash Message
Save 22
setting 20
use 10
Lamp 20
Save 23
Up/using Speed Dial
Speakerphone 4
set 20, 21
Select/de-select 22
20
Speakerphone 8
Show Phone
Selecting
Use
Speakerphone 10
Screen 20
Call
Alternate Display
Speakerphone 11
Speed Dial 21
Appearance/Feat
key 30
Speakerphones 10
Yes 19
ure Button 30
speakerphone 10
Speed Dial List
Yes 20
Display Mode 21
Use 10
Access 8, 9
Yes 21
Selecting 21
Use 30
menu 21
Yes 23
Selecting 30
User Labels 22
Speed Dial List 8
Yes/No 19, 23
Set
Using
Speed Dial List 9
Your Speed Dial List
Flash Message
EU24 Expansion
Speed Dial List 21
18
Lamp 20
Module 30
Speed Dial Number
Show Phone
Using 30
Dialing 14
Screen 20
Using Self Test 21
5420/2420 Phone User Guide
Page 33
IP Office
Issue 6d (15th September 2005)
2420user
Performance figures and data quoted in this document are typical, and must be specifically
confirmed in writing by Avaya before they become applicable to any particular order or contract.
The company reserves the right to make alterations or amendments to the detailed
specifications at its discretion. The publication of information in this document does not imply
freedom from patent or other protective rights of Avaya or others.
Intellectual property related to this product (including trademarks) and registered to Lucent
Technologies have been transferred or licensed to Avaya.
All trademarks identified by the ® or TM are registered trademarks or trademarks, respectively,
of Avaya Inc. All other trademarks are the property of their respective owners.
This document contains proprietary information of Avaya and is not to be disclosed or used
except in accordance with applicable agreements.
Any comments or suggestions regarding this document should be sent to
"wgctechpubs@avaya.com".
© 2005 Avaya Inc. All rights reserved.
Avaya
Sterling Court
15 - 21 Mundells
Welwyn Garden City
Hertfordshire
AL7 1LZ
England
Tel: +44 (0) 1707 392200
Fax: +44 (0) 1707 376933
Web: http://www.avaya.com
5420/2420 Phone User Guide
Page 34
IP Office
Issue 6d (15th September 2005)
